Wilson 801212 In-Vehicle Wireless 50 dB Dual-Band Signal Booster Kit [Discontinued]
Availability: Out of stock
You Should Choose This Kit If
You need the most powerful car & truck signal booster available that can boost the 2G and 3G networks from most carriers to multiple phones and data devices simultaneously. The In-Vehicle Kit comes with a 12 in magnetic antenna that sticks to the roof of your vehicle and includes a cable that runs in through a door and attaches to the In-Vehicle Amplifier. It is powered using a 12V adapter that plugs into a cigarette lighter or 12V power port. The inside antenna connects to the inside antenna port on the amplifier and should be located close to where you typically use your phone.
Will This Work For Me?
The In-Vehicle Kit is our most powerful signal booster designed for use in a car, truck, or other similar vehicle. It will boost the signal for multiple phones and data devices at the same time. When there is a medium strength outside signal, you'll be able to use your phone anywhere within 4 to 6 feet from the inside antenna. In areas where the existing outside signal is very weak, your phone or data device will have to stay within 6 to 12 inches from the inside antenna to receive the boosted signal.
For the strongest signal boosting possible, you can use the Cradle Plus as an inside antenna which will limit the system to one phone only, but that phone will get the strongest boosted signal possible and is ideal for locations with a very weak signal. For this system to work, there must be some existing signal to boost so if you're in a complete deadzone with no service for miles around, it's likely that no signal booster will work.
The In-Vehicle Kit improves the signals used for both voice calls and Internet access. In areas with a weak signal, the In-Vehicle Kit will reduce dropped calls, improve call clarity and increase Internet data speeds.
All carriers that use the standard dual band frequencies (800 MHz & 1900 MHz) for voice and 3G data, including:
- AT&T 2G/3G/4G HSPA+ (shows as 4G on your phone)
- Verizon 2G/3G
- Sprint 2G/3G
- US Cellular 2G/3G
- Alltel 2G/3G
- T-Mobile 2G only in most locations
- Major Canadian Carriers 2G/3G
- All other carriers using 800 MHz and 1900 MHz
- Will not boost 4G LTE for any carrier
- 801201 - 50 dB Mobile Wireless Dual-Band Amplifier
- 301103 - 12" Magnetic Mount Antenna with FME-Female Connector
- 301127 - Slim Low-Profile Antenna with FME-Female Connector
- 859913 - DC to DC 6V Power Supply Kit
There are many accessories available for the In-Vehicle Kit. For the strongest signal boosting possible, you can use the Cradle Plus as an inside antenna instead of the included slim antenna. To power the In-Vehicle Amplifier, you can use the included DC Power Adapter or the optional AC Power Adapter. For a more permanent installation in your vehicle, you can use the hardwire power adapter.
Installing the In-Vehicle Kit is very easy and because nothing is permanent, it can be moved from one vehicle to another.
Mount the included outside antenna on the roof of the vehicle. Route the attached coax cable in through a door opening. To protect the cable, run it under the door seal. Connect the cable to the In-Vehicle Amplifier. Plug the included slim inside antenna into the Inside Antenna port on the amplifier. Then just plug in the included power adapter and connect it to the In-Vehicle Amplifier. When you place your phone near the inside antenna, you should see a stronger signal (it may take up to 30 seconds for your phone's signal strength display to update). If you already have a strong outside signal, you won't see any benefit from the In-Vehicle Kit so try it in a place where you typically have signal trouble.
|System Type||Wireless Coverage over a very small area|
|Gain||50 dB for both 800 MHz and 1900 MHz with Automatic gain control|
The maximum coverage area will be highly dependent on the existing outside signal strength. In areas with a moderate existing signal, you may get coverage up to 6 ft. from the inside antenna. In areas with very weak existing signal, you may only get coverage up to 6 to 12 inches from the inside antenna.
|Connectors||Amplifier has FME-Male Inside & Outside Antenna Connectors|
|Power Requirements||6 V, 0.5 A - 1.5 A (subject to uplink power)|
|User and Installation Manual||User and Installation Manual|
|Frequency Bands||800 MHz, 1900 MHz|
|Specific Frequency (Up/Down)||824 - 849 MHz / 869 - 894 MHz, 1850 - 1910 MHz / 1930 - 1990 MHz|
|Noise Figure||3 dB nominal|
|isolation||> 90 dB|
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.
Please note, the four largest carriers - AT&T, T-Mobile, Verizon and Sprint - and more than 90 regional carriers have given blanket consent for use of all boosters certified to the new FCC standards.