Wilson 460105 AG Pro 70 Dual-Band 70 dB Yagi Kit for Voice, 2G & 3G [Discontinued]
Availability: Out of stock
Regular Price: $649.99
Special Price $578.99
The Wilson 460105 AG Pro 70db Dual Band Signal Booster Kit with Yagi Directional Antenna is one of the most powerful signal boosters available that has been certified under the new FCC regulations. It is perfect for situations where you have a weak outside signal and need a high powered antenna to target your carrier's nearest cell tower and maximize the coverage area inside of the home or office. This kit boosts the frequencies used for voice calls and 3G data by the major carriers in North America, and includes everything you need to get started. Please note that this kit will not boost the 4G LTE frequencies used for broadband speed data by any of the carriers.
Many variables impact the total coverage area of a signal booster system. The following are estimates only and may not be accurate in any individual situation.
- If you have an existing strong 5-bar outside signal, you may get up to 10,000 sq ft of coverage inside*
- If you have an existing 3 to 4-bar (-90 dB) outside signal, you may get up to 7,500 sq ft of coverage inside*
- If you have an existing 1 to 2-bar (-100 dB) outside signal, you may get up to 2,000 sq ft of coverage inside*
The Wilson 460105 AG Pro 70 Dual-Band 70 dB Yagi Kit for Voice 2G & 3G boosts the standard dual-band frequencies of 800 and 1900 MHz which are widely used in North America. The following carriers are supported:
- AT&T 2G, 3G and 4G HSPA+ (not 4G LTE)
- Verizon 2G and 3G
- Sprint 2G and 3G
- T-Mobile and Cricket 2G
- Virgin Mobile 3G
This system does not support 4G LTE, WiMAX, Nextel/iDEN/MIKE, or AWS networks.
The Wilson 460105 AG Pro 70 yagi kit is a complete kit with everything needed in one box. Some installations may require additional parts so see the Accessories section below.
- Wilson AG PRO 70dB Amplifier
- Wilson 304475 Multi-Band High Gain Yagi Antenna
- Internal 301155 panel antenna
- 60ft and 75ft LMR400 coaxial cables
- Instruction manual with installation directions
We recommend a lightning protector kit for all installations in areas that have lightning or thunderstorms. The lightning protector has a gas discharge element that severs the connection to the amplifier if the outside antenna is struck by lightning.
The included directional outside antenna comes with mounting hardware for a pole. If you don't have an existing pole to mount the antenna to, you should also include 901117 Pole Mounting Assembly.
The Wilson 460105 AG Pro 70 yagi kit is easy to install for anyone that's a bit handy. But if you're not comfortable getting up on your roof to mount an antenna, it may be best to find an electronics installer or a handy friend. We always recommend doing a soft install where you don't permanently mount anything or drill any holes until you know the system will work for you and you've identified the best locations for the antennas. To install, just follow these 4 steps:
- To start, you'll need to find a place on the roof of your home or office to mount the outside antenna. With a directional outside antenna, it's best to figure out which direction it will need to be pointed before permanently mounting the antenna which we'll cover at the end. Connect the 75 ft. WILSON400 coax cable to the antenna and run it into the building. You may be able to enter through a vent or a soffit; otherwise, you may have to drill a hole.
- With the cable inside, connect it to an in-line lighting protector if you purchased one, and then to the amplifier. To the inside antenna port on amplifier, connect the 60 ft. WILSON400 cable and then connect the inside antenna. If you have an attic, the easiest installation method is typically to have the amplifier and inside antenna in the attic with the panel antenna face down on the floor in the middle of the house. If you don't have an attic, you can mount the panel antenna on the ceiling in the middle of the house, or on a wall.
- Once all of the components are connected, plug in the amplifier and see if you get any error lights. For any errors, consult the manual or contact us for help.
- For best results, you'll need to aim the directional outside antenna. Start with the antenna high on the roof pointed in one direction. Turn on the system and have an inside helper inside stand about 3 ft. from the inside antenna and take a signal reading with their phone in field test mode. Rotate the directional antenna 45 degrees and then pause for 30 to 60 seconds. After the pause, the person inside should take another signal reading, and then you can repeat the process. Each time your partner checks the signal strength, also check to make sure there aren't any warning lights on the amplifier. After you've gone all the way around, mount the antenna facing in the direction with the strongest signal. If possible, also mount the antenna on that side of the home or office so that it's pointing away from the building and not over the building.
The included manual is very helpful and we recommend reading through it before beginning the installation. If you run into any issues, feel free to contact us for help.
* The actual coverage area of a signal booster is dependent on many factors including existing outside signal strength, obstructions between you and the cell tower, the materials used in your home or office, the layout of the area you need to cover with a boosted signal, and other factors. The approximate coverage areas listed above are estimates. Actual coverage area will vary based on these and other factors. If you're not sure if a system will be powerful enough for your needs, contact us to find out.
|System Type||Wireless Coverage - can use phone as you normally do within coverage area|
|Coverage Area||Up to 20,000 sq. ft.|
|Power Requirements||110-240 V AC, 50-60 Hz, 8 W|
|User and Installation Manual||No|
|Frequency Bands||800 MHz, 1900 MHz|
|Specific Frequency (Up/Down)||824 - 849 MHz / 869 - 894 MHz, 1850 - 1910 MHz / 1930 - 1990 MHz|
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.
Please note, the four largest carriers - AT&T, T-Mobile, Verizon and Sprint - and more than 90 regional carriers have given blanket consent for use of all boosters certified to the new FCC standards.